Estudo comparativo do efeito da aplicação de zinco como camada intermediária em soldas dissimilares produzidas por soldagem a ponto por fricção (FSpW) entre as ligas AA5754 E AZ31
Visualizar/abrir
Data
2015Autor
Orientador
Nível acadêmico
Mestrado
Tipo
Assunto
Resumo
Neste trabalho foi realizado um estudo comparativo entre juntas dissimilares produzidas pelo processo FSpW sem e com a utilização de Zn como metal intermediário tendo a finalidade de investigar a eficácia da adição deste metal no comportamento mecânico das juntas, bem como avaliar sua influência nas características microestruturais das juntas soldadas. As juntas foram produzidas com ligas de Al AA5754-H24 e Mg AZ31-O, de particular interesse do setor automotivo. Nas condições de soldagem com me ...
Neste trabalho foi realizado um estudo comparativo entre juntas dissimilares produzidas pelo processo FSpW sem e com a utilização de Zn como metal intermediário tendo a finalidade de investigar a eficácia da adição deste metal no comportamento mecânico das juntas, bem como avaliar sua influência nas características microestruturais das juntas soldadas. As juntas foram produzidas com ligas de Al AA5754-H24 e Mg AZ31-O, de particular interesse do setor automotivo. Nas condições de soldagem com metal intermediário, chapas de Al revestido com Zn por galvanização foram usadas. As propriedades mecânicas das juntas foram avaliadas através de ensaios com carregamento quasi-estáticos e dinâmicos, sendo então correlacionados com as características microestruturais. Através das análises constatou-se que a aplicação de Zn como metal intermediário mostrou-se efetiva na redução do volume de compostos intermetálicos formados na interface da solda e consequentemente, obteve-se um aumento do desempenho mecânico de cerca de 48 % no ensaio de cisalhamento por tração, 230% no ensaio de tração cruzada e de 35,31 % no ensaio de fadiga quando em comparação a juntas soldadas diretamente entre as chapas de AA5754-H24 e AZ31-O. ...
Abstract
In this research was carried out a comparative study between dissimilar joints produced by means of the process FSpW without and with applying Zn as an intermediary metal with the purpose of investigating the effectiveness of the addition of this metal in the mechanical behavior of joints, as well as to assess its influence on the microstructural characteristics of the welded joints. The joints were produced with the AA5754-H24 Al alloy and the AZ31-O Mg alloy, materials of particular interest ...
In this research was carried out a comparative study between dissimilar joints produced by means of the process FSpW without and with applying Zn as an intermediary metal with the purpose of investigating the effectiveness of the addition of this metal in the mechanical behavior of joints, as well as to assess its influence on the microstructural characteristics of the welded joints. The joints were produced with the AA5754-H24 Al alloy and the AZ31-O Mg alloy, materials of particular interest to the automotive industry. For the welding conditions with the Zn interlayer Al sheets coated by hot deep galvanizing were used. The mechanical properties of the welded joints were evaluated in terms of quasi-static and dynamic load and then correlated with the microstructural features. Through the analyzes it has been verified that the addition of Zn as an intermediary metal proved to be effective in reducing the amount of the intermetallic compound formed at the weld interface and consequently the mechanical performance increased about 48 % in the lap shear strength test, 230 % in the cross tensile strength test and 35,31 % in the fatigue test when compared to the welded joints produced by the direct contact among the AA5754-H24 and the AZ31-O sheets. ...
Instituição
Universidade Federal do Rio Grande do Sul. Escola de Engenharia. Programa de Pós-Graduação em Engenharia de Minas, Metalúrgica e de Materiais.
Coleções
-
Engenharias (7319)
Este item está licenciado na Creative Commons License